VIEW THIS AS

Auto mode follows the Route Engine until you choose a viewpoint.

YOU ARE HERE

ROUTE CHECK

CONNECTED TO

WHAT NEXT

Use the canonical route for this room, or HELP if you are unsure.

Bukit Timah Secondary 1 Design and Technology | From Design Brief to Tested Paper Prototype

Three secondary students review open books and notes together in a classroom.

A Secondary 1 Design and Technology project can start with something as ordinary as a return slip getting lost under a pile of papers. A good design brief describes who experiences the problem, where it happens and what an improvement would let that person do. This Bukit Timah guide takes two fictional school situations from brief to paper prototype, then uses test results to show how a student can decide what to change.

Design and Technology sits in the lower-secondary common curriculum under Full Subject-Based Banding. The examples here use folded paper or thin card, a ruler, a pencil and removable tape. Students can follow them on a clear table or work through the evidence on paper. Use your teacher’s brief, materials and instructions for school assignments. Before you build, write down what the user must be able to do and how you will tell whether your idea helps.

  • Observe one difficulty and describe it in the user’s terms.
  • Turn the brief into a few requirements you can check.
  • Sketch two ideas before folding either one.
  • Test the same task in the same way for both ideas.
  • Record what happened, make one change and test again.
  • Explain what your paper model shows and what still needs testing.

1. Read the situation before drawing a solution

A teacher has put a folder on a table beside a whiteboard. During the last five minutes of a lesson, students return one small slip each. Some students place their slips on the table rather than inside the folder. An assigned class helper later collects the slips, but has to look underneath worksheets and check the other end of the table. A possible assignment might say, “Create a paper model of something that helps students place their return slips where the class helper can find them.”

Start with what you know. The person returning a slip needs to recognise where it goes. The helper needs to collect it. The setting is a shared classroom table with other papers on it. The five-minute detail describes when the problem occurs. It tells you that a user may be moving quickly, although you would need more information before saying that time pressure causes every mistake. Notice how one short description gives you evidence about a setting and leaves questions about individual behaviour.

A student might write, “Some return slips get left outside the folder and are difficult for the helper to find among other sheets.” That is a useful problem statement. It points to where a design could make a difference. A sentence such as “The desk needs a blue box” belongs later in the process. It names one object and one colour before the student has decided whether the difficulty concerns visibility, access, labelling or something else.

Try a simple check. Ask a family member to read your problem statement and name the user and the difficulty without looking at the original story. If they can name only “students” and “papers”, add the missing action. If they can tell you that the helper needs to find the returned slips in one place, the statement gives enough direction to sketch. If a classmate suggests a difference you had overlooked, record it as a question before you add it as a requirement.

The MOE lower-secondary Design and Technology syllabus describes learning through designing and making. In this practice guide, you can see those activities in a cycle of investigating, generating and developing an idea, making a model, testing and deciding what to improve. Classroom projects can use different materials, tools and ways of recording the work. Follow the instructions issued for the current project. MOE Full Subject-Based Banding common-curriculum overview · MOE lower-secondary Design and Technology syllabus

Contents · Next chapter

2. Write a brief and decide what counts as success

A brief turns a situation into a job. For the return slips, try this version: “Design a tabletop return point for students to place a slip and for the class helper to remove the collected slips at the end of the lesson.” A brief like this gives the student responsibility for developing the response. It allows a pocket, tray, standing sign with a marked area, or other shape to remain in consideration.

For the paper model, use an 80 mm by 40 mm slip drawn on an existing scrap of paper. You can bring a page to the right size by folding along ruler marks and using the resulting folded section as the slip. Use the same type of paper for every practice slip so that the comparison stays simple. Mark a rectangle 140 mm wide and 120 mm deep on a larger sheet to represent the available space on the shared table. These are fictional practice dimensions. A real project can start with the actual space, if the teacher asks you to measure it.

A first requirement is that the model fits within the marked rectangle. Measure the widest and deepest parts once it stands on the table. A second is that the user can find the correct opening or marked area and place the slip in one continuous action. Decide in advance what will count as a placement. For this practice, the slip is placed when it stays in the target area after the user lets go. A third requirement is that the helper can remove three slips without taking apart the model. Each requirement describes something you can observe.

Write a distinction between a requirement and a preference in your notes. “Fits inside 140 mm by 120 mm” is a requirement for this exercise. “Use green lettering” is an optional preference unless you have a reason to make it necessary. If the model is hard to read, try a label with clear lettering and check it from the user’s approach. You can learn more from that observation than from picking a colour early and keeping it unchanged.

Try the requirement test with a new sentence. A friend proposes, “Students should be able to see the label.” Ask them where the student is standing when this matters. You could revise the sentence to “A person approaching from the front can say what belongs here before handling the slip.” That statement lets you run a test. It also helps you check whether the label makes sense, since a visible label reading “Place here” may still leave the user wondering what to place.

Keep the requirements short enough to use while you work. Write each one on a separate line, leave room for a measurement or an observation, and number the lines to match your sketches. If an idea meets the main action requirement but spreads across the table, the space measurement tells you which part still needs work. This record also gives you something concrete to discuss when two people in the group favour different ideas. Ask each person to point to a requirement and explain how their choice might address it.

Previous chapter · Contents · Next chapter

3. Sketch two models with different strengths

Draw the first model as a shallow tray with a folded front lip. Show the slip entering from above. Next, draw a standing pocket with the label high on its front and an opening at the top. Add one small side view for each. A side view helps you see whether a child has to lift the slip, angle it, or push behind a fold. Use arrows to show how the slip travels in and how the helper takes it out. Label the arrows so a reader can tell whose action each one shows.

Suppose your shallow tray sketch measures about 120 mm wide and 90 mm deep, including its side folds. The front lip rises about 15 mm. The model could use one sheet folded into a broad, shallow shape. Its label might be placed on the base near the front. This makes the label easy to see while the tray is empty. It may gradually be covered as slips build up. Mark that as a prediction you can check.

The standing pocket remains within the target area if its base is about 110 mm wide and 85 mm deep. It gives a high space for a label and leaves room on the table, but an upright shape may lean or slide if the slip catches the lip. Show where you intend to brace the fold with removable tape. If a paper mock-up will naturally lean, note which edge rests on the table and how the tester approaches. A small fold can change the whole action.

Build a rough version of each with paper, pencil marks and tape. It is enough if the shape holds while you try the motion. You can also demonstrate a sketch by placing flat paper pieces where the walls, label and slip would go. If the paper tray spreads and its footprint exceeds the limit, record the measured footprint. You can bring the sides closer and brace a fold before using it for the main comparison. Put the measured width and depth beside the sketch so another person can follow what actually happened.

Before leaving this stage, check a simple dimension. The slip is 80 mm across its long edge. A pocket entrance that is 80 mm wide may catch the slip at the corners if it arrives at a slight angle. An opening near 100 mm gives some extra space. Try the actual paper shape with your sample slip before making a final sketch. The size that matters is the usable gap between folds, tape or walls. A ruler reading across the outside edges of the pocket can be wider than the real gap.

Previous chapter · Contents · Next chapter

4. Run the same task on both return point models

Keep the table layout, approach, slip and instruction the same for both models. Place three blank sheets at one side to represent the other papers. Put the model inside the marked rectangle. Ask the tester, “Please put this return slip where it belongs.” Say the same words each time. Give the tester enough time to find the label and place the slip. If they ask what to do, note the question before giving help. The question can be evidence about the design.

For a classroom or family demonstration, a tester’s identity adds little to the record. Use trial numbers. One person can try both models, but their second attempt may benefit from knowing what the task is. A second person can begin with the other model if available. You can practise from the fictional results below if you are working alone. These numbers illustrate how to reason from a record. Your own test may produce a different pattern.

Check Shallow tray Standing pocket
Measured footprint 124 mm wide by 96 mm deep 112 mm wide by 88 mm deep
Slip placed without extra help 3 of 4 attempts 3 of 4 attempts
Hesitation or difficulty One person paused over the loose worksheet next to the tray One slip caught at the opening and the person asked whether to push
Helper removed three slips together Yes No, because the near edge sat below the front wall

Both models meet the space requirement. Both have three placements without help out of four. That shared count can hide a meaningful difference. The tray had a problem with recognition, while the pocket had a problem with physical access. The pocket also missed the removal requirement. A reasoned decision is to take the tray forward because the helper could collect the slips and the next thing to check is clear. Another student might choose the pocket if space is needed nearby and the removal difficulty can be fixed with a shallower front. The decision should follow a stated priority and the recorded evidence.

State the limits of four attempts. You can describe what happened in this small classroom-style demonstration and identify an improvement worth trying. You have limited evidence about how often the problem would happen during a school week. Someone who has spent several minutes listening to a project explanation may also perform differently from someone seeing the object for the first time. Write down any condition that could change the reading of your results.

Previous chapter · Contents · Next chapter

5. Revise one feature and use the same check again

Take the shallow tray forward. The problem to investigate is whether the label is visible and specific enough beside other loose sheets. Put the words “Return slips” on a folded paper sign at the back of the tray, with the lettering facing the approach. Leave the tray size, front lip and location alone. Changing one feature gives you a better chance of connecting a different result to the sign.

Use the earlier task again. Cover the base of the tray with three slips to represent a fuller tray, and keep the other loose sheets nearby. To make the comparison meaningful, test the first tray again in the same fuller condition before checking your revised version. A student who compares an empty original with a full revised model has changed more than the location of the sign. Set both models up under the same conditions, and record which one the tester sees first.

Suppose a teacher gives you this fictional comparison. With the full tray and the label still flat on the base, two of four users place the slip without pausing to ask. With the raised sign, four of four place it without asking. Both trays let the helper remove three slips. In one revised trial, the folded sign shifted when the user reached in. Your notes now support a careful claim: “In this four-attempt check the raised sign improved recognition. I also found that I need to keep it in place when the tray is used.”

That claim works because it connects an observation to a change and acknowledges something new. A final sentence such as “The raised sign makes every student use the tray correctly” would reach beyond the evidence. It is more useful to say exactly when it worked and what the next check would be. You could try securing the sign lightly and ask two people who have never seen the model to use it. Record whether they can still remove three slips and whether the sign stays visible when the table has its normal papers.

A design record can be short. Save the first sketch, the small table, one revised sketch with an arrow marking the extra sign and a final sentence. Put the pieces in order. Someone reading the page should be able to point to the result that led to the revision. Your actual schoolwork may call for a different format, so follow your teacher’s requirements for photos, drawings, notes and the way you acknowledge feedback.

Previous chapter · Contents · Next chapter

6. Work through a second brief for a shared book

A class borrows one reading copy during quiet reading. It alternates between two locations: on the borrowing table when available, and at a reader’s desk while in use. Without a clear signal, someone waiting to borrow it sometimes searches both places. The class can move a small paper marker on the table. The assignment is to devise a marker that tells a classmate whether the reading copy is available, and allows the student returning the book to update its state quickly.

This brief is different from the return point. The slip model asked a person to locate a destination and perform a physical action. The book marker asks a reader to understand a status. The first user needs to interpret a sign. The other user needs to change what it shows. You can check both using role-play. For the reading task, ask, “Can you borrow the reading copy now?” For the updating task, say, “The book has just been returned. Change the marker.” Decide ahead of time how you will judge each response.

A first design is a double-sided tent made by folding a piece of paper. One long side reads “Available”, and the other reads “In use”. The person changing the state turns the tent around. A second design is a flat base divided into two labelled positions with a paper arrow that can be moved by hand. In either case, use bold pencil lettering and read from roughly the same place. You can place a ruler or draw a pencil line beside the model to mark the approach for each attempt.

Before anyone tries the tent, walk to the other side of the table. A person there may read the opposite state. That is a weakness if people come from both sides. The arrow marker could also confuse a reader if both labels are visible and the arrow can sit between them. A good sketch can reveal both possibilities. Annotate the first sketch with approach arrows and the second with the position you want the arrow to occupy after each change. Labels are useful if they describe what a person must do, such as “Place arrow completely inside one marked box.”

Previous chapter · Contents · Next chapter

7. Test what the reader understands and check both tasks

For the tent, let the first reader approach from the front with the “Available” message facing them. Ask your question and record the answer. Reset the same state and approach from the other side. In the fictional example, the answers are “Yes” from the front and “No” from the back. They cannot both describe the true state. The update is easy, but the design gives conflicting information from two plausible approaches. The problem is the layout of the two messages.

Now try the flat base and arrow. Set it to “Available”, then invite a reader to approach from the front and another from the side. Suppose both recognise that the book is available. Give a different person the updating task. In this example, the person moves the arrow towards “In use” but leaves its tip on the dividing line. The next reader asks which side counts. You now have a concrete repair opportunity. The marker needs to help the person changing it select one position clearly.

Replace the dividing line with two separate outlined boxes. Leave their labels and the size of the base the same. Add a short instruction to place the whole arrow inside a box if your teacher allows it, then record that you changed both the separation and the wording. If you want to learn which feature produces the improvement, try the boxes first and add the instruction in a second version only if the updater still needs it. It is reasonable to change two details at once for a final refinement if the aim is to improve a design, and to be careful about what your test can show about each change.

A brief example of a completed record might read, “Version one gave two different answers for the same book state, depending on where the reader stood. Version two showed the same state to both test readers, but the arrow could be left on a line. In the next version I gave the arrow two clear places to sit. The updater moved it fully inside one box on both trials and the reader answered correctly.” A final check would include setting both states and testing the reverse change. A model that handles only “Available” leaves half the job untested.

If you share a test with a classmate, give them room to do it their way. Ask them to tell you what they think the sign means before you explain the answer. Record their answer and what they did with the paper. That gives you more to work with than a yes-or-no question about whether they like the model. If their idea for a change sounds useful, say what part of the test it addresses and decide how you would check the change.

Previous chapter · Contents · Next chapter

8. Transfer the method to a new situation

Choose one of these invented situations and spend ten minutes on a first attempt. A group needs to leave a note on a shared desk showing that its display is ready for a teacher to see. A borrower needs a clear way to return a paired set of cards without leaving one behind. A student needs to show two other group members which of three pages should go on top of a shared folder. Each problem asks for an action you can describe and try with paper.

Here is a worked starting point for the paired cards. The users are the student handing back the set and the student checking it next. The problem is that one card can remain on the desk while the other goes into the return point. You might sketch a sleeve that accepts both cards, or a flat card with two marked positions where the student lays the pair before returning it. For either model, try a complete pair and a missing card. Check whether the next reader can spot the missing card and whether the full pair can be collected in one action.

If the flat design shows a missing card clearly but the full pair can slide off when collected, try a folded paper band. Test whether it holds both cards together and whether a person can tell that only one card was inserted. A new feature may help one requirement and make another harder to check. A short comparison tells you whether the extra security changes visibility. If it does, return to the brief and decide which action matters most or adjust the feature again so it can meet both requirements.

To finish the independent exercise, write four lines. State the user’s difficulty, the requirement you checked, the result and the next change. For example, “The next borrower needs to see both cards. With the two marked positions they noticed the missing card immediately. They picked up the complete pair but one card slipped out. I will test a paper band with both positions still visible.” Each line should help another person know what was tried and what would happen next.

Previous chapter · Contents · Next chapter

9. Bring useful evidence to school

If your child wants help with a project, ask them to bring one sheet showing the idea before and after a change. A parent might ask where the user stood, what the user could see and what the record says. The student can do the folding, make the drawings and write the decision. That leaves a piece of work they understand and can explain at school. When the teacher suggests a change, ask your child to predict which result the change will affect before they build again.

The word “prototype” here means a trial version made to learn about an idea. Paper can reveal whether a hand can reach a slip or a reader can make sense of a marker. A paper version gives limited evidence about how a design would hold up with different material, heavy use or changes in the setting. You can name those limits in one sentence and ask the teacher which of them matter for the current stage. That is part of using evidence responsibly.

SEAB lists G1 Design and Technology as K124 in its 2027 school-candidate Secondary Education Certificate syllabus. That syllabus describes the later upper-secondary subject and its assessment. It can help families understand where design investigation and practical project work may lead. At Secondary 1, check the lower-secondary curriculum and your teacher’s current brief. Ask the school about the actual offerings and cohort examination requirements when upper-secondary choices are due. SEAB 2027 G1 Design and Technology syllabus K124

For a next step, choose one test your child can explain without opening the notebook. Ask what they were checking and what changed after the test. Then return to the page and compare their account with what they recorded. If they can point to the user’s action, name the evidence and say what they would test again, they have a useful basis for their next classroom project. Bukit Timah Secondary 1 Design and Technology subject guide

Previous chapter · Contents

All Bukit Timah Secondary 1 G1 subject guides