Looking for a Bukit Timah SEC Design and Technology tutor? For the 2027 Singapore-Cambridge Secondary Education Certificate (SEC), the school-candidate syllabuses are G1 K124, G2 K234 and G3 K345. Families can contact eduKateSG near Sixth Avenue MRT to discuss their child’s learning needs and ask whether small-group D&T theory and practice support is available.
Design and Technology, or D&T, asks students to understand a need, think through alternatives and explain how a proposed design works. A student may want help reading a mechanism diagram, explaining why a design suits its user or working through a fresh sketching exercise. The school supervises the assessed design project. The activities below use original, unrelated practice examples for building skills independently.
- G1 K124: Paper 1 is 1 hour and worth 30%. The individual design project lasts 20 weeks and is worth 70%.
- G2 K234: Paper 1 is 1 hour 30 minutes and worth 40%. The individual design project lasts 20 weeks and is worth 60%.
- G3 K345: Paper 1 is 2 hours and worth 40%. The individual design project lasts 22 weeks and is worth 60%.
- Project calendar: The published durations run from the question paper release and exclude school holidays. Use school instructions for actual dates, milestones and submission details.
- Project supervision: Check questions about the assessment with the school’s coursework supervisor. Keep outside practice on independent tasks and examples.
- Tuition enquiries: Share your child’s level, examination year and a non-assessed piece of theory or design practice.
Find the information you need
Contents
1. Check the subject, level and examination year
The 2027 SEAB school-candidate lists identify Design and Technology at G1 as K124, at G2 as K234 and at G3 as K345. The respective reference codes for 2026 and earlier are 7062, 7055 and 7059. Match the examination year and syllabus code before using a past paper or topic list. A question about a familiar mechanism can still be useful for learning, provided its content and level fit what the student is studying and its format is understood. 2027 G1 school-candidate list · 2027 G2 school-candidate list · 2027 G3 school-candidate list
A child might already know D&T from a lower-secondary common-curriculum lesson. Upper-secondary SEC D&T is an examined subject with its own written paper and individual project. When Secondary 2 students are choosing upper-secondary subjects, ask which combinations and levels the school offers and what will be considered for selection. A Posting Group helps determine secondary school entry and starting subject levels. The school-confirmed D&T level is the one to use when buying materials or planning for the national exam. eduKateSG guide to common-curriculum and SEC D&T
D&T also has a particular way of working. A student might enjoy drawing and still need time to check dimensions or explain what the drawing shows. Another may be keen on gadgets and need to get comfortable considering several alternatives before focusing on a preferred idea. Ask your child which part of a previous school task they enjoyed and which one they found hard. Their answer can lead to a more specific course conversation than an overall idea of being “good at making things”.
If a child sees similarities between D&T and Electronics, Design Studies or Art, look at the actual subject documents. In D&T, a student develops a response to a user need and communicates how the design works. The balance of written and project work, and the technologies covered, are part of that choice. If D&T is being considered for a future course, ask the receiving institution which subjects and grades apply to the intended intake. The school’s Education and Career Guidance team can help identify the information to check. eduKateSG guide comparing upper-secondary creative and applied electives
2. Read the two assessment components at your level
At G1, the written paper lasts 1 hour, has 50 raw marks and contributes 30% of the subject grade. All five questions are compulsory. Questions 1 to 3 are about applying design knowledge and carry 18 marks together. Questions 4 and 5 concern mechanisms and electronics and carry 32 marks together. The design project runs for 20 weeks from the question paper release, excluding school holidays. Its rubric totals 70 marks and the project contributes 70% of the grade. SEAB 2027 G1 D&T syllabus K124
At G2, Paper 1 lasts 1 hour 30 minutes, has 60 raw marks and contributes 40% of the grade. All three questions are compulsory. Question 1 accounts for 24 marks of design knowledge application, and Questions 2 and 3 account for 36 marks in mechanisms and electronics. The design project runs for 20 weeks from the question paper release, excluding school holidays, and its 60-mark rubric contributes 60% of the grade. SEAB 2027 G2 D&T syllabus K234
At G3, Paper 1 lasts 2 hours, has 80 raw marks and contributes 40% of the grade. All four questions are compulsory. Question 1 covers design and carries 26 marks. Questions 2 to 4 carry 54 marks together and cover structures, mechanisms and electronics. The design project runs for 22 weeks from the question paper release, excluding school holidays. Its rubric totals 60 marks and the project contributes 60% of the grade. SEAB 2027 G3 D&T syllabus K345
A written answer often draws on two skills at once. It might require naming the part of a mechanism and showing how its movement solves the problem in the question. A diagram may need labels that communicate how a proposed design would be held, used or moved. When reviewing a school practice paper, group together two errors that come from the same skill. A diagram missing the direction of movement and a paragraph saying “the part turns” without specifying how may point to the same gap. Practise showing input and output clearly before taking on another whole paper.
Raw marks show what a paper or task is marked out of. Weight shows how much the component contributes to the overall subject result. Some figures happen to match, such as the G2 written paper and project each having 60 raw marks. The written paper still contributes 40% and the project 60%. Use the weighting to understand why the course contains both an extended practical process and a written examination. Plan time for theory during the coursework months alongside the school’s obligations.
3. Follow the school’s coursework and submission instructions
The three syllabuses describe Paper 2 as an individual coursework examination based on an examination question. It contains a Design Journal and Presentation Board. The journal is a record of the student’s actual design process. It shows how the student reached decisions and incorporates the mock-up or mock-ups and resulting prototype. The assessment documents specify A3 sheets secured together or A3 sketchpads for the design sheets, alongside the physical materials listed in the syllabus. The Presentation Board communicates the proposed solution and its key features using up to two single-sided A2 boards. Ask the school how it wants the student to prepare, label and submit the materials. K124 project requirements · K234 project requirements · K345 project requirements
Teachers serve as coursework supervisors. They facilitate and assess the project and can advise the candidate in that capacity. The work is marked internally and moderated externally. Bring questions about what the student can do, the use of resources and how to record any guidance to the school supervisor. The student completes the assessed design decisions, documentation and making under the school’s instructions. Families seeking external practice can choose generic theory or use a separate design exercise that is unrelated to the live project. The practice activities on this page are for that purpose. G1 coursework supervision · G2 coursework supervision · G3 coursework supervision
The durations in the syllabuses are measured from the examination question paper release and exclude school holidays. Use the school’s own dates for the release, check-ins, workshop access and final submission. The publicly published SEC framework places written papers other than English and Mother Tongue in the October to November window. It gives a broad written exam period. For actual submission dates and exact paper dates, rely on the school’s 2027 coursework instructions and SEAB’s detailed examination schedule when available. SEAB SEC timetable framework · eduKateSG SEC timetable and study guide
Bring administrative questions to the coursework supervisor
A family can ask which date marks the official start, where the student can see published school milestones, and how to report an absence. They can also ask how the school handles access to workshop sessions, the use of materials and the safeguarding of work between lessons. If a student is considering a source, tool or outside activity connected with the project, ask the supervisor first whether it is permitted and how the student should record its use. Procedures can depend on the assessment and the school’s current instructions.
Find out whom the student should contact if an approved material is unavailable. A school might offer a process for obtaining a similar item or direct the student to use a resource already provided. Let the student explain the problem to the supervisor. Practical help at home can be as simple as leaving time for the student to send that message, then making sure the family has saved the reply about dates or arrangements. Keep design choices, project documentation and anything to be submitted with the student and the school assessment process.
Support the school timetable at home
When a student has several subjects due together, parents can help by putting school-confirmed dates on a shared calendar. Ask your child to tell you what the next school session is for and what the teacher says they should bring. If a workshop slot was missed, ask the student to contact the supervisor to find out what the school can arrange. These steps make space for the student’s planning and decision-making while respecting the assessment.
The published syllabuses describe the Design Journal as a record made in real time and advise candidates against reworking design sheets. The student can ask the supervisor how to deal with a missing note, a change to the design or an unexpected result. A design process can include decisions that change when new evidence arrives. Give the student time to explain what happened and what they need to ask their teacher, even if the first thing they say is that the idea “didn’t work”.
4. Practise thinking through a design with a separate example
These short exercises are for independent practice away from the live assessment. Use ordinary paper, a pencil and light household objects. They are small enough to do by hand and give students a chance to explain decisions without a school workshop. Keep machine work and actual coursework with the school’s supervision and instructions.
Make a design brief specific enough to test
Imagine an organiser at a table in a school exhibition wants visitors to read a card that names the exhibit. A card lying flat is partly hidden by a display object. The card must remain easy for the organiser to switch when the next exhibit comes in. Ask the student to identify the user and write a brief one-sentence design aim. A possible aim is to make a tabletop holder that raises an exhibit card so a visitor can read it while the organiser can replace it quickly.
Have the student write two testable specifications for a paper-scale version. A model should support a standard index card upright for one minute on a flat table. The organiser should be able to remove the card and insert another without lifting the holder. Each statement describes a result a student could observe. If the specification simply says it should be “easy”, ask which action would let the student test that claim.
Now draw two options. One uses a long slot supported by folded paper. The other uses a back support and a raised lip under the card. Ask the student to label a feature that helps the card stay up and a feature that makes replacing it easier or harder. The student can decide what to explore. For instance, a holder with a deep front lip may hold the card securely but obscure the bottom line. A student who spots the trade-off can consider changing the height of the lip before drawing a final version.
Compare paper models under the same conditions
For a paper-only practice, make two low stands and use the same card. Keep the card size, table surface and time in the test the same. One model can have a wide base and the other a narrower base. Give a light, comparable tap on the table beside each model and see what happens to the card. Record the result in a sentence. If the wider one stays up in the trials and the narrower one tips, the test suggests a wider base could help in that set-up. Record how much extra space it needs on the table before deciding it is the better choice for this display.
A one-off result can lead to another question. Did one card lean more than the other, or did one model sit on the edge of a mat? Repeat the comparison with the test surface and angle held steady. If both models stay up, ask whether a visitor can still see every line or whether the organiser can switch the card easily. A model gives the student some evidence about the feature tested. The question should tell them what to check next.
Try a new design context independently
For a second exercise, imagine a volunteer needs a paper tabletop sign that shows either “open” or “full”. Ask the student to draw two options, one that flips and one that slides. Each drawing should show the user’s action and what somebody facing the sign sees. The student can then choose one constraint and compare the two options. If the sign sits directly beside a wall, a sliding change might need room at the side or might be easier than flipping over the back, depending on how the parts are arranged. A sketch seen from above can make the answer clearer. This exercise tests whether a student can carry over the user–action–result reasoning from the first example.
Practise a drawing that another person can interpret
For a fresh, non-assessed example, give the student a rectangular paper sleeve with a paper tab sliding out one side. Measure the sleeve with a ruler. Have the student sketch what they see from above and from the front. In the top view, they can use an arrow to show how the tab slides, then add the overall length and the width that determines whether it fits the sleeve. In the front view, they can show which part is open. If a dimension is meant to guide the size of the slot, ask them to point to exactly where it applies.
Now ask another person to use only the sketches to say which way the opening faces or which part moves. If they hesitate, ask what information would remove the uncertainty. A dimension helps when the uncertainty is about size. A second view helps when one view hides a face. A clearly placed arrow helps when the issue is direction. The student can try any one of those changes, see whether the other reader interprets the sketch correctly and then decide what to retain.
Change the object to a paper carton with a hinged flap. Ask the student to select the two views that would best show both states. Give them room to decide how to show the movement and which labels to use. Comparing the two exercises teaches why a type of drawing is useful in a particular case. It also shows the difference between making marks to remember an idea and communicating an idea clearly enough for someone else to understand it.
5. Work through theory using sketches and explanations
Read the input and output of a lever
Picture a light paper-scale model of a counter sign. Its moving arm pivots on an imaginary pin. One end of the lever is pressed down, and a sign on the other end rises above the counter. Draw a side view and mark the pivot between the two ends. Put a downward arrow near the end the user presses and an upward arrow at the sign end. The points on both sides move about the pivot. The arrows show the starting direction of each end and make the described mechanism easy to follow.
If the distance from the pivot to the point where the user pushes is increased, the same turning effect can be produced by a smaller push in an ideal example where the force is perpendicular to the arm and the load stays the same. Hold the output arrangement fixed while thinking about that change. Then ask which problem the change might create. A longer handle could need more room to move. A good answer links the physical change to the user’s experience and the space available.
For a short transfer check, move the pivot to the other side of the section of the arm that carries the sign. Ask the student to draw the arrangement before deciding what happens when the handle is pressed. If both points are now on the same side of the pivot on the same straight arm, they move in the same starting direction. The drawing should let another student check this without having to guess where the pivot is.
Explain a switch without building a circuit
Imagine a display cabinet should light up only while someone holds a separate button. Give the student a paper diagram with a cell, lamp and normally open push button in one loop. When the button is pressed, it closes the gap and the lamp lights. Releasing the button opens the gap and the lamp goes off in the ideal circuit. Ask whether the same component is suitable for someone who wants the lamp to stay on while both hands are moving an object. A switch that remains in the selected position would meet that second requirement. The student needs to describe which user action keeps the circuit in the required state. Keep this question on paper.
For G3, explain what changes when a frame is braced
Imagine a rectangular frame for a very light paper notice. If its corners can rotate, a sideways force can make it lean into a slanted shape. In a sketch, add a diagonal member between opposite corners. The diagonal creates two triangles and limits the frame’s change of shape in the idealised example. Ask the student to shade the two triangles and show the direction of the sideways force. A complete response connects the extra member to reduced sideways distortion. It can also mention a constraint such as the brace crossing a space someone needs to keep clear. A written paper may frame a question differently, so use the school’s practice materials to check the syllabus skills.
Read the command word and complete the reasoning
A written question that asks the student to state a feature can often be answered with a short, precise phrase. A question that asks them to explain why the feature works needs an additional relationship. For example, “wider base” identifies a feature of the card stand. An explanation would say how the wider base gives the stand more room to lean before its centre of mass passes beyond the footprint, which reduces its tendency to tip in the simplified example. The surrounding conditions, including the position of the load, still matter. An answer should use the information and level of detail asked for in the question.
A question that asks for a comparison needs both choices discussed on a common basis. For the stand, choose a factor such as space occupied or ease of exchanging the card. Explain how each option performs on that same factor. To practise, give the student the same two options and ask first for one feature, then for an explanation, and then for a comparison. When reviewing the responses, mark where the student’s treatment of the same information changed in response to the instructions. The student can repeat the pattern with a new set of diagrams without being prompted with the first answer.
6. Decide whether your child needs support
Look at a recent theory question or an unrelated school practice exercise. Identify the first step at which progress stopped. A student who can name a switch and cannot explain what it does in the circuit needs to rehearse the two states with the loop drawn. A student who can draw a familiar object and stalls on an unfamiliar context can practise a side view and plan view of an everyday object before adding more detail. A student who keeps losing marks after choosing a good idea can practise linking each design feature to a specific problem named in the question.
A parent can review that link without marking the whole answer. Ask what the user does first, which part changes, and how the student knows the change meets the need. If the answer is easy with a familiar exercise, change one condition or use a new sketch a few days later. The new attempt helps show whether the explanation can be produced independently. Ask the teacher for targeted advice when the same missing skill keeps appearing in written practice.
Ask what makes D&T a good subject choice for this student
Bring two samples of lower-secondary schoolwork to the subject-choice conversation. One can show an exercise the student liked and the other something they found slow or difficult. Ask the student what they did when a first idea did not fit the task. Did they research a user’s needs more closely, try another drawing or investigate why a model behaved differently than expected? Enjoying that revision process is useful information alongside grades and the school’s selection advice.
Ask whether the student enjoys both shorter theory problems and a longer project. Find out where workshop sessions fit in the timetable and what happens if the student has a planned school activity at the same time. If D&T is one of several electives the child finds interesting, compare what they would be doing in a typical week and ask about each course’s assessment components. A timed question and an extended school project place different demands on the student. Understanding both can support a choice the student can sustain.
Plan study time around school commitments
In a busy week, choose one written practice skill and one review task. Early in the week, practise interpreting a small diagram, such as a mechanism with a missing movement arrow. Later, use a changed diagram and ask the student to explain both the input and output. Keep the working visible so the student can compare the two attempts. When using a timed school practice paper, begin by giving enough time to read the diagrams and instructions. Then shorten the task gradually before increasing the number of questions attempted.
Once the school has confirmed project milestones, plan unrelated written practice around them. Put school sessions and other subjects on the calendar first and work out what time is realistically available for revision. A short task that a student can explain afterwards gives more information about an issue than a large pile of completed sketches. Near the written paper, bring in question types from several topics so the student can choose the right method while dealing with an unfamiliar setting.
Enquire about Bukit Timah support
Families can contact eduKateSG’s Bukit Timah centre at 8 Fourth Avenue, Singapore 268674, near Sixth Avenue MRT, to ask whether suitable small-group support is available for D&T theory, diagram reading or design practice using unrelated examples. Bring the school-confirmed syllabus level, a non-assessed practice question and the student’s first attempt. For assessed coursework requirements, direct questions to the school’s coursework supervisor. Contact eduKate Singapore
More eduKateSG guides
Secondary 4 G2 Design and Technology guide · PSLE, Full SBB and secondary pathways
Explore the other SEC subjects — Computing · Nutrition and Food Science · Art
