In Secondary 1 Design & Technology (D&T), your child can turn a design brief into a simple model by asking who will use it, what they need to do, and where they will do it. D&T is part of the lower-secondary common curriculum under Full Subject-Based Banding. A pupil who enters through Posting Group 2 learns it alongside mixed-form classmates. Follow your child's school brief and project instructions for the materials, stages and evidence expected.
At home, try the smallest model that can answer a useful question. Fold or tape paper and light card, test the design with a willing user, and change one part in response to what happened. A paper model can show whether an opening is easy to find, a label stays visible or two parts fit together. Keep the first sketch and one clear test observation so your child can explain the revision.
- Start with the user’s task. Say who needs to do what, where and under which constraints.
- Sketch different ways to do the job. Label what the user touches, moves, sees or reads.
- Build a quick paper or card mock-up. Use it to test one uncertain feature before making the complete idea.
- Watch the test and keep the result. Record the conditions, what happened and what you will change.
- Follow the teacher’s instructions. Keep school workshop processes and assessment requirements with the school, and use safe tabletop models for home practice.
Find your next step
Contents
Read the brief and plan
Make and test a prototype
Improve the design and explain why
See how the design project fits Secondary 1
Under Full Subject-Based Banding, D&T sits alongside other lower-secondary common curriculum subjects, such as Art and Food & Consumer Education. The pupils in a mixed form class can share a D&T learning experience even though they may take English, Mathematics and Science at different subject levels. Posting Group 2 is how the child entered school. The school brief tells them what task to complete in the common D&T curriculum. If the timetable shows separate D&T and Food & Consumer Education blocks, use the instructions for the appropriate class. The common curriculum and mixed form classes
The published lower-secondary D&T syllabus describes learning to identify needs, set a brief, develop ideas through sketches, build quick models, and plan prototypes. It asks pupils to consider the user, purpose and setting and make practical design choices. It also addresses using materials, structures, mechanisms and electronics through suitable school activities. At home, a piece of folded card can help with the early questions. Workshop methods and materials belong under the school's training, supervision and safety procedures. Lower-secondary Design & Technology syllabus
The school determines the project students actually work on and how they document it. West Spring Secondary School has published an example of a Secondary 1 design-and-make project involving a light and pencil holder, and describes sketching, mock-ups, developed ideas and prototypes as components of lower-secondary work. Yishun Secondary School likewise explains why its lower-secondary programme uses freehand sketches and tactile models. Those published examples show what the process can look like. Ask your child's school for its current brief and instructions before buying supplies or assuming a project follows another school's sequence. West Spring Secondary School’s D&T curriculum Yishun Secondary School’s Craft and Technology programme
Recognise what each object in the design process is for
A sketch helps the pupil imagine or explain an idea. The designer can draw an opening from two angles, show what a hand touches, or decide where the join should go before building anything. A mock-up is a quick physical representation for thinking and testing. It may model just one feature, such as the height of a front lip. A developed prototype can demonstrate more of the intended operation in suitable materials under the school process. Each form of representation answers a question the pupil has reached at that stage.
Suppose your child builds a sleeve that should let a user slide paper cards out. A folded copy-paper model is enough to see whether a hand can reach the card. It may also help measure the opening. If the future version uses stiff material, do not infer its lifespan from the paper. State what was tested and what depends on a later material decision. This is a useful distinction in an evaluation. A precise sentence about what a quick mock-up established is better evidence of thinking than a large claim about how the imagined final product would perform.
Keep later subject choices in their own place
At upper secondary, a student may be considering an elective offered at their school. SEAB lists a G2 D&T national examination syllabus for the 2027 examination cohort. The project and national assessment arrangements for that later course serve a different purpose from a lower-secondary introductory task. Follow the Secondary 1 teacher's stated brief and deliverables. A small home exercise can build the habits used later without borrowing an upper-secondary time requirement or marking scheme. 2027 G2 SEC subject listings eduKateSG’s guide to G2 D&T and the SEC
Turn a vague brief into something the child can test
Begin by reading the school brief aloud. Ask the student to circle the user, underline the action and draw a box around the location, material or size conditions. If the brief says a design should help a classmate find a needed card at a shared desk, the designer needs to understand how the classmate searches now. Does the classmate identify cards by colour, letter or position? Does a notebook cover them? Are the cards brought out in a set or carried one at a time? The answers lead to different designs.
A need describes a difficulty in a situation. A brief states the intention for a design. Specifications describe what the proposed solution should do, often in a form that can be checked. For example, the need might be that a student cannot find the correct prompt quickly when cards are stacked flat beside an open exercise book. The brief might be to design an organiser so the student can identify and remove a chosen prompt at that shared desk. The specifications could say it must hold three sample cards, show each card's identifying letter, fit within a defined paper rectangle and allow one card to be removed while the other two remain in place.
Observe one attempt at the task
Give the user a reasonable version of the existing situation. Ask them to find a named prompt from the three cards while their book occupies the desk area. Let them attempt the task without announcing the design you have in mind. They might move the book, pick up the entire stack or stop to read each line. Write down one thing they did and one question about it. “She lifted the whole stack and checked the bottom card” is an observation. “She would like a wider pocket” is a design guess until you ask or test it.
When the pupil needs a simple interview, ask a neutral question such as “What part took the longest?” or “Which card was difficult to reach?” Give the user a chance to point. The user may explain that the first letters were hidden or the cards felt too similar. A question like “Would you love it if I made it in green?” tends to draw an answer about the designer's preference. Colour could later help the user identify choices. Discover what the current task actually requires first.
Decide which constraints are given and which you can choose
A school brief may specify a material, a dimension or a user group. Copy those details into the sketch notes accurately. Do not move from a fixed 16 cm space to a 20 cm model unless the task permits that change. Other requirements emerge from observation. If the pupil discovers that cards need both a letter and a short word to be recognised, they can add them to a design specification. Write which condition came from the brief and which came from the user. This shows why a later change was reasonable.
Turn broad words into things you can see or measure. “Compact” may mean that the model fits inside a 16 cm by 12 cm rectangle of paper. “Easy to use” may mean that the test user can find the requested card and remove it without lifting other cards. “Clear” may mean that the three letters can be read from the seated position. Choose a few tests suited to the brief. A number such as 16 cm is useful only if it reflects the real space or the teacher's stated constraint. The model will teach you more when its success criteria match what the user actually needs.
Choose what you will test first
Some risks can be investigated early with a crude shape. If a pocket conceals a letter, ask whether it happens with a single pocket before building three. If a part fits only when pushed hard, a paper sample can help the designer see which edge catches. If someone needs to reach a card from the side of a desk, mark the desk boundary and test one mock-up at that angle. Put a short question at the top of the model notes. “Can the user read B while all the cards are in place?” gives the tester a job and gives the designer an observation to record.
Be careful about making the success test too narrow. A card may be readable after the designer moves it towards the user. The criterion says it should be readable in the organiser. Ask the user to sit in the normal position and leave the model where you intend it to go. A first quick test can be improvised, while the notes should still say what conditions were used. This keeps the results comparable when a revision is made later.
Sketch alternatives that change how a design works
Sketch three arrangements quickly before choosing one. For a prompt organiser, one option might have three card slots across the front. Another might stack the cards in steps so their top letters remain visible. A third might hold cards in a single spread with paper dividers. The alternatives use the desk space and the user's reach differently. Drawing one slot in red, blue and green would explore identification by colour but would not explore a different shape or way of using the card. If colour is the uncertainty, test colour. If access or footprint is the uncertainty, sketch different structures.
Write short labels that explain purpose. “Front lip stops card from sliding” tells the reader why a line matters. “Each tab marks an independent pocket” explains how the user knows what to pull. Use an arrow to show direction of movement when necessary. Add a top view if the model needs to fit within the space, and a side view if the angle or height matters. For a home sketch, clear proportions and labels are enough. At school, use the drawing conventions, dimensions and format the teacher specifies.
Choose a promising idea with a reason you can check
Ask the student which design best supports the main task. Maybe the three slots are easy to recognise, while the arrangement is wider than the allowed space. The stepped design may fit and still risk hiding the lowest letter. The divider design may reduce width, while a card could catch on a fold. List one advantage and one question for each option. Pick the option you can make with the available time and that teaches you something important if it fails.
Write the reason in one sentence and connect it to the brief. “I chose the stepped arrangement because it fits the small space and I can test how much of each letter will remain visible.” This gives the model a clear task. If the card is still hard to find, the design can change. Keep the older sketch. A useful feature in one of the other ideas may become the solution to a problem you only discover after testing.
Worked example. A prompt card organiser for a shared desk
This invented home example starts with three prompt cards about 6 cm wide by 8 cm high. Write A, B and C near the top edge of the cards in large letters. The pupil's user is a classmate who needs to pick a named card while keeping an exercise book open. Mark an area 16 cm wide by 12 cm deep on a piece of scrap paper to represent the desk space. Use one open notebook or a sheet drawn to its size beside the area. The cards, model and book can all stay on the table. A parent can act as a willing test user.
Keep the materials light. Use paper, thin card from a clean empty carton, a ruler, pencil and removable tape. Fold paper to size or tear it along a crease if that suits the material. A household adult can prepare the edges if cutting is needed. Use only the tools your household and school allow for the practice. Avoid making the mock-up rigid or adding a heavy book as a load. The question concerns the user's ability to read and remove a card from a safe tabletop model.
Build just one pocket first
Take a strip of paper long enough to wrap loosely around the bottom of one card. Crease it so the card slips into a low open pocket with a back and a front lip. Keep the top half of the card visible. Set it on the area drawn on the table and ask the person to remove the card and put it back. If the folds lie too tightly against the card, remake the sleeve with a little room on both sides. If the whole pocket lifts when the card is pulled, tape the pocket's base to a card backing and repeat.
Write down what the first pocket tells you. “The sleeve was as wide as the card, and the paper corners caught. Making a little extra space let the card slide without pulling the sleeve up.” The sentence explains the necessary change without making the whole organiser. The first pocket has answered a question about fit. The model still needs to test visibility across a set and how removal affects the remaining cards.
Build the stepped layout and record the first test
Make two more pockets of the same width and tape them in three rows from the seated person's side of the desk toward the back. Space them so a card fits in each pocket and each can be reached. Use light folded paper pads under the middle and back pockets to raise them in steps. A 1 cm pad under the middle and a 2 cm pad under the back are starting dimensions for this exercise. Measure the actual footprint and adjust the paper layout if the backing goes beyond the permitted rectangle. The three pockets should use the depth for separation and preserve width beside the notebook.
Give the user one test instruction. “Without moving your book, pick card B and leave the other two in the organiser.” Set the model squarely within the marked area. Put the cards in A, B and C order before the first test and avoid pointing to B. Watch where the user's eyes and hand go and note whether a different card was displaced. Repeat with cards shuffled if you want to test whether the person is reading the labels instead of memorising the locations. Write down the legibility and the result of picking a card separately.
Suppose the test user can read A and C from the seat but leans forward to distinguish B. They pick the right card, and the front pocket shifts when their hand brushes it. Make two notes. “B took a second look from the seated position.” “Front pocket moved when B was removed.” The first suggests a visibility problem and the second suggests a space or attachment problem. They might have different causes. Solve one first so you can see which change mattered.
Revise one feature and use the same conditions
Keep the seat position, card lettering and notebook location. Raise the middle pocket another centimetre if the backing can support it, or let B extend a little higher from its own pocket. Choose one change. Repeat the same task and record whether B can now be read from the seat. Check what happens to C. An improvement to the middle row can hide part of the rear row. Test the letters together even when you changed one pocket.
Next, address the moving front pocket. Secure only the pocket's base with tape where the model allows, or shift the front row a small distance to create more finger space. If the footprint is already at its limit, make the change within the existing boundary. Repeat the test and record what the other cards did. After the two separate changes, run one complete trial to see whether the set still does all the required jobs together. The trade-off becomes visible when the pupil measures and observes the design in use.
Write the three lines that explain the result
Begin with the need and criterion. “My user needed to retrieve one of three prompts beside an open notebook without dislodging the others.” Follow with the relevant evidence. “With the first arrangement the tester leant forward to check B and moved the front pocket while lifting it.” End with the change and what the repeat test showed. “I raised the middle pocket, then widened the gap to the front pocket within the same footprint. Suri read B from her seat and the other cards stayed in place in the repeat test.” Use an actual observation from the practice instead of copying an invented result as your own.
A final note can identify the remaining question. “I tested with one person from this side of the table. I still need to see whether someone seated to the right can see C.” That is a useful next move if the real brief covers a shared table. It also keeps the claim honest. A positive result from one sitting may justify keeping the idea for now while leaving other uses to be tested.
Worked example. A paper sleeve that lets a user return a slip
This second invented task concerns a school club that temporarily sets aside slips marked “to check”. A student needs to place a small paper slip in its assigned sleeve while keeping the sleeve on a flat table and without moving a notebook. The brief says the opening needs to be easy to recognise and a slip should stay visible enough to remove. For this exercise the slip is 5 cm wide by 7 cm long. A maximum footprint of 10 cm by 12 cm leaves room for the notebook. Use only scrap paper, light card and tape.
First, ask someone to try pushing a slip into a folded paper sleeve with both edges flush. Watch their first movement. They may turn the entire sleeve around, pinch the two sheets apart, or use the slip's corner to lift the flap. Write what they actually do. If a notebook makes one side crowded, start with the sleeve oriented as it would be in that space. A user who can enter the slip from one side may struggle when that side sits against the book.
Compare two different openings
Make one small sleeve with a back flap that extends above the front flap by about a centimetre. The user can see the lower edge of the front and use the visible rear surface to guide the slip. Make another sleeve with a diagonal fold at one top corner of the front so part of the back surface shows at that corner. Keep both sleeves comfortably wider than the slip and tape each base to a same-size scrap backing. Check that a slip inserted most of the way still protrudes at the top. Choose how far you will insert it during the tests.
Ask the same person to put a slip into each sleeve and take it out once using the same table and notebook positions. In each run, lay the slip flat in the same starting place and give the same instruction. Notice whether the user has to push open the pocket, move the notebook or use a second hand to keep the sleeve still. A trial confined to a normal seated position says more about desk use than an adult holding the sleeve up in the air for the child.
Suppose the longer back flap helps the user find the opening but the thin paper still lies flat against the front, making insertion difficult. The diagonal fold forms a clearer entry for a person approaching from the right. A left-side approach puts the fold farther away. Both versions meet part of the brief. The designer can select one and change its orientation, or keep a guiding rear flap while giving the front edge a shallow crease that maintains a little separation. Use this trial to choose the next test rather than naming an absolute winner for every user.
Choose the next test based on the user
If the user regularly sits at the left half of the desk, test that approach first. Swap the diagonal fold to the other corner and change nothing else. Check whether the user's first insertion goes smoothly and whether the slip comes back out easily. If either opening becomes too wide and loose, the slip may drift sideways. Add a small folded paper guide within the sleeve only if the next test shows this is a problem. That change aims to guide the slip, and a repeat test can show whether it also makes insertion stiffer.
If the same sleeve should work for people on either side, try a small central opening made by folding the top front edge down near the middle, with the two edges kept at the same height. Test both approaches and note which part the user reaches for first. The model can stay a flat paper envelope on the same backing. This keeps the task safe and makes the revised feature easy to see. A successful trial on a paper slip only supports use with the paper size and model you tested.
Add a checking step without creating new clutter
Ask the user how they know the slip needs checking. A word beside the opening may be more useful than a coloured stripe if the sleeve is mixed with others. Write “to check” in large letters and place it where the slip will not cover it. Put the sleeve beside another plain envelope and ask the user to set the slip aside without prompting. Watch whether they read the label or identify the sleeve by position. A label can be legible and still lie in the wrong place for the visual task. Record a change in the label location only if the results support it.
If your child adds two labels and an arrow at once, try isolating what helped. A word may direct the choice. The arrow may aid entry once the sleeve is found. Keeping those jobs separate makes revision easier. A child who can explain the two jobs has learned more than someone who simply says the finished version looks better. A good design journal keeps the effect of each feature connected to the user's action.
Worked example. A sliding paper strip for a classroom routine
A fictional class helper needs to show which of three classroom tasks is next. The brief is to make a tabletop cue showing “return cards”, “close folders” or “check table”, one at a time. The cue should stay on a small rectangular surface, be readable by a classmate in front of it and change without taking it apart. The user is the helper who moves the strip and the classmate who reads the cue. Those two people have different jobs and both need to be included in the test.
Use a sheet of paper on the table as the base. Fold two short strips to make wide, flat guide loops and tape their ends down, leaving room for a paper strip to slide underneath. Lay one opaque paper panel above the first part of the path and one above the last part. Leave an uncovered space between the panels wide enough to read one message. You can tape the panels down using folded paper supports where needed. The opening is the space between the two pieces, so no hole needs cutting. Allow clearance under the panels so the thin strip can move freely. The user keeps the base on the tabletop while moving it.
Write the three task names along a separate long strip of paper. Place each message in its own equal-width section. Fold the strip lightly at the boundaries if that makes the spacing easier to lay out, then flatten it so the creases do not catch. Leave blank paper toward both ends to form pulling tabs. Centre the first message in the visible opening and move the strip to the other two positions. Tape a paper marker beside the opening when you know where each message should line up. Lay the first paper mock-up flat. There is no need for a casing or for heavier materials to learn whether the cue can be aligned.
Test movement and reading as two jobs
First ask the helper to show “close folders” and then “check table” without moving the base. You can sketch a small outline on the table to see whether the base shifts. Watch how the user grabs the strip and where it catches. Then ask the other user to read the cue from the normal position across the desk. If they read fragments of two different messages at once, record which words appear together and where the strip was positioned. You can improve alignment and reading as separate tasks.
Suppose the helper pulls the tab too far on the first attempt. The middle of the window shows “folders” and the beginning of the next message “check”. The reader hesitates, while the base itself stays still. Try adding simple alignment ticks just outside the window for the helper. Match each tick to a position on the strip. Retest the same switching task. If the user cannot see the ticks from their side, move them closer to that side within the paper model. Watch whether the design cues the helper without covering the displayed text.
If the strip catches only when pushed, compare pulling from either end. The thin paper may bend under a pushing action and stay flat when pulled. You can widen the guide loops by a small amount while keeping the window unchanged, or give both ends enough tab space to pull in either direction. Test one of these changes first. A stronger pulling tab might improve comfort and still leave the guiding issue unresolved. Recording exactly what was changed helps the student explain the result.
Describe what the paper model can establish
Your child might conclude, “The helper could reveal each cue without moving the base once the position marks were visible. Our reader could recognise the text in each position from across the desk.” This is a statement about the model and the user test. The family can also record that the paper edges softened after repeated handling or that the test included only one person reading. If the project eventually calls for a different material, a teacher can guide the pupil on how to investigate it at school.
Notice what the three worked examples have in common. Each includes a specific task and limits on where it happens. Each uses a small physical question to find a problem before the object is fully developed. The first investigates visibility and retrieval of cards. The second investigates opening and slip insertion. The third investigates a person moving information into the right position for another person to read. The tests are different because the intended actions are different.
Run a short test your child can explain later
Write the test question before making changes. “Can the user remove the named card while the other two stay put?” or “Can the helper align three messages without lifting the cue?” Then list what will stay the same. Candidates include the seated position, table space, card size, directions given, materials and time allowed. A school project can use the teacher's preferred test plan. For home practice, a one-page note beside the mock-up is enough.
A useful sequence is baseline, test, change and repeat. The baseline might be testing the existing pile of untouched cards. Record what happens and why the current situation creates the need. Then use the paper model in as similar a situation as possible. Decide which change to make and repeat the same task. Adapt the conditions for a second test only when you can explain the reason. Testing with the model at an angle may be useful for a design that will be shared from two seats. It tells you something new about location rather than merely repeating the first result.
Separate an observation from the reason you think it happened
An observation is something the student saw or measured. “The sleeve moved 2 cm toward the user.” A possible explanation is “The card caught against the narrow edge and the user's pull moved both parts.” Another explanation is that the tape pulled away. If the student cannot tell which occurred, ask how they could find out. They might look at the tape after the movement, or try the same insertion with a wider pocket and check the result. This turns a reasonable hunch into a new test.
A compliment is a form of feedback. It tells the student the user liked something, while leaving the performance question open. If a person says “It looks good”, ask which part was easiest to use and which part they had to stop and think about. If they say “I could see B only after I moved my book”, put that detail alongside the intended use. The early model can be visually simple and still answer the design question. Give the pupil time to write down the useful words before decorating anything.
Use results that fit the scale of the test
A small home trial can record whether a task was completed, how many attempts were needed, which part moved or whether a measurement fits inside the boundary. It can also record a user comment in their own words. If you time a trial, be clear whether the user had a chance to practise first. A second attempt can improve because the user knows the target, even if the model stayed the same. Change the card order where appropriate or give the learner a fresh test user. Note that limitation if a second user is unavailable.
Avoid trying to make the model pass a heavy load test. The scrap pieces described here are for testing paper movement, positions and hands using lightweight materials at the table. A school design may require a more formal test or a safer supervised method for strength and stability. Ask the teacher what testing the project expects. At home you can still learn a great deal by watching a paper part catch, slide, fold or hide a label.
Make a small record for three independent checks
A little table in the pupil's notebook can help when there are several criteria. Use one row for the footprint, one for the reading task and one for movement. Beside each criterion write the condition and the observation. For the card organiser, the condition for the footprint might be “base rests inside the marked 16 cm by 12 cm area”. The observation might be “base fitted, rear pad extended behind the line”. That gives the child one specific change to consider. It also shows why measuring the backing on its own would miss part of the model.
For the reading row, write where the user sat and which letter they were asked to find. An observation could say “Read A and C seated. Leant over to read B.” For the movement row, record what the other cards did when B was lifted. The child can report a good result on one criterion alongside a weak result on another. Avoid changing a successful feature just because the result was uneven. The next test should address the need that still matters.
Mark the place on the drawing where a feature will change. If the pupil used an outline rather than a full-size drawing, add one actual measurement beside the feature. A 1 cm gap can look larger in a close-up sketch. Labelling it makes it possible to build another version with the intended clearance. If your child is unsure where to measure, identify the two edges or faces that define the gap. It might be the distance between the front of one sleeve and the back of the next, or the free width inside a pocket rather than its outside width.
After the revision, use the three rows again. A backing that fits, a legible card and a steady pocket are three separate results. Write the next question only after checking the three conditions together. This shows why a small number of precise criteria is easier to work with than a long list of general hopes.
Keep the design journal close to the actual work
Use the format the school assigns. For practice, keep the first sketch, a corrected sketch, and a record of one trial. Write the date and the model version so the child can refer back to it accurately. A test record can be short. State the brief or criterion, describe the model, write what you asked the user to do, and say what happened. Add the one change you made and how the repeat test went. Where photos are permitted, a top or side view can help show a changed dimension, without including any person who did not agree to be photographed.
Write the test notes when the model is still on the table. Small details are easiest to remember then. The child may have thought the card fitted because their own hand could lift it, while a second user grasped it differently. Ask which difference belongs in the journal and what the result suggests. A failed mock-up or an untidy crease can be worth keeping if it shows what needed to change. A later illustration can explain the fold more clearly. Keep the connection to the actual model visible.
Show a meaningful revision
A pupil who says “I made it better” can improve the journal by naming the original condition, the design change and the relevant test result. For example, “The front edge sat flush with the back, so the tester pinched the two pieces apart. In the revision I folded the front edge away slightly. The tester placed the slip without pinching open the sleeve.” The advantage here is the link among a part, an observed task and a change. That is information a teacher or another student can act on.
If an improvement created another problem, record both results. Raising a pocket can expose its letter and obscure a different one. A wider sleeve can ease entry and permit the slip to move farther inside. Keeping the real trade-off gives the next model something specific to address. One version may already be suitable for the brief even if it has a remaining drawback. Explain how important that drawback is for the intended user and what would justify spending a second round on it.
Give help that leaves the design with the child
A parent can act as a user, ask what the child is testing, hold a ruler still, or prepare a card edge the household has decided should be managed by an adult. Let the student decide which model to try and explain the next change. If an adult sees an improvement immediately, ask what the pupil observed first. Give them time to choose whether that evidence points to the same improvement. Sometimes the child is exploring a different problem, and a plausible adult idea would interrupt a useful test.
A compact home session can have three stages. Spend a few minutes reading the brief and marking the user and constraints. Give the pupil time to sketch and build one part. Finish with a trial and one sentence about the next version. An optional follow-up on another day gives the child a chance to see whether they remember the reason for the change. With a school deadline nearer, look at the teacher's expected output first and use the session for the remaining part the child is allowed to work on at home.
Questions families ask about Secondary 1 D&T
Do low Mathematics scores tell me my child will struggle with D&T?
They do not establish how the child will approach a design task. Geometry, measurement and comparisons can help with the work. So can careful observation, the ability to imagine a fold and readiness to revise a model after watching someone use it. Start with a practical job the child can see. Ask them to measure the available desk width and draw the boundary before comparing two sketches. Give a precise bit of measurement support if they need it.
Can my child start with a drawing of the finished product?
Yes, as an initial idea, if it helps them explore the task. Ask them to label one thing it is meant to let the user do and sketch another way to achieve the same thing. The first drawing might eventually become the chosen idea. The second makes it possible to explain why the first suited the brief. A paper test can reveal whether the initial shape gives the user the access or movement the drawing suggests.
When should we seek the school's materials guidance?
Use the teacher's current instructions for any assessed project, required material, tool or workshop method. For the exercises in this guide, use paper or light card on a flat working surface. If the design depends on how a firm joint or a different substance will behave, bring that question to the teacher. The school can guide the actual making and testing under its procedures.
Should a good design change after feedback?
Change it when an observation shows the current version misses an important criterion or a smaller revision can make the intended action easier. Keep it when the evidence supports the job and a proposed change would add complexity without a relevant benefit. Write down why. The discussion is about evidence, the intended user and the specific task. A child can improve a design by simplifying a feature when the test shows it distracts or obstructs.
Where does this fit with the rest of the common curriculum?
Use this guide for practising the particular D&T sequence from a written brief through a quick paper test. Follow the school's programme for the rest of the materials and topics, and use the school's separate instructions for Food & Consumer Education. For a broader view of class projects, making and shared lower-secondary lessons, read the eduKateSG guide to D&T under Full Subject-Based Banding.