VIEW THIS AS

Auto mode follows the Route Engine until you choose a viewpoint.

YOU ARE HERE

ROUTE CHECK

CONNECTED TO

WHAT NEXT

Use the canonical route for this room, or HELP if you are unsure.

Speed–Time Graphs: Interpreting Acceleration, Distance and Units

Three learners review open books together at a classroom table, with stacks of textbooks, stationery and a whiteboard in the bright room.

The worked examples assume motion along a straight line without a change of direction within each stage. On any speed–time graph, gradient is the rate of change of speed. Under the straight-line assumption, this gives tangential acceleration; a velocity–time graph is needed to track signed motion. Constant speed alone does not imply zero acceleration when direction changes, as in circular motion.

A speed–time graph rises from 0 to 20 m/s in 5 seconds, stays flat for 10 seconds, then falls back to 0.

What does the slope mean?

What does the area under the graph mean?

On a speed–time graph, height is speed, gradient is the rate of change of speed, and area under the graph is distance travelled.

This is different from a distance–time graph, where gradient itself is speed.

The quick answer

  • Horizontal segment above zero → constant speed.
  • Horizontal segment on the time axis → stationary.
  • Positive gradient → speed increasing.
  • Negative gradient → speed decreasing.
  • Gradient = change in speed ÷ change in time, with compatible units.
  • Area under graph = distance travelled.

Speed is the vertical coordinate

If the graph shows 12 m/s at t=4 s, then the object’s speed at that time is 12 m/s.

No gradient calculation is needed to read the speed itself.

Always ask what the vertical axis measures. On a speed–time graph, the graph’s height gives the speed directly.

Gradient is the rate of change of speed

Suppose speed increases from 0 to 20 m/s in 5 s.

Acceleration:

Δv/Δt=(20−0)/(5−0)=4 m/s².

The unit m/s² means the speed changes by 4 m/s each second.

Constant speed in a fixed direction has zero acceleration

If the graph is horizontal at 20 m/s from t=5 s to t=15 s, speed stays constant.

Gradient=0.

Acceleration=0.

The object is still moving because graph height is above zero.

This is where distance–time and speed–time graphs differ

Horizontal on a distance–time graph means stopped.

Horizontal above zero on a speed–time graph means moving at constant speed.

The same visual shape can mean something completely different when the vertical variable changes.

Negative gradient means deceleration of speed

Suppose speed falls from 20 m/s to 0 in 4 s.

Gradient:

(0−20)/4=−5 m/s².

The negative sign shows speed is decreasing.

In elementary speed–time interpretation, this is often described as deceleration.

Area under the graph gives distance

Why?

Speed×time = distance.

On the graph:

  • vertical dimension = speed;
  • horizontal dimension = time.

So graphical area has units:

(m/s)×s=m.

That is distance.

The area rule is dimensional mathematics made visible: speed multiplied by time produces distance.

Triangular acceleration stage

Speed rises uniformly from 0 to 20 m/s over 5 s.

Area:

1/2×5×20=50 m.

The object travels 50 m during the acceleration phase.

Rectangular constant-speed stage

Speed=20 m/s for 10 s.

Area:

20×10=200 m.

Triangular deceleration stage

Speed falls uniformly from 20 m/s to 0 over 4 s.

Area:

1/2×4×20=40 m.

Total distance for all three stages:

50+200+40=290 m.

Trapezium area for changing speed

Suppose speed increases uniformly from 10 m/s to 18 m/s over 6 s.

Area under graph is a trapezium:

1/2(10+18)×6.

=14×6.

=84 m.

This also equals average speed over the interval times time because uniform acceleration makes average speed (u+v)/2.

Average speed from total area

If total area under a non-negative speed–time graph is 290 m over 19 s:

average speed:

290/19≈15.26 m/s.

The whole-journey average is total distance divided by total time.

A speed–time graph cannot go below zero

Speed is a magnitude and is non-negative.

A graph below the time axis would normally be a velocity–time graph, where negative values encode direction.

Speed and velocity are not interchangeable. A speed–time graph stays at or above zero; a velocity–time graph can cross below zero when direction reverses.

Velocity–time extension

On a velocity–time graph:

  • gradient still represents acceleration;
  • signed area represents displacement;
  • area below the axis contributes negative displacement.

Total distance would require adding magnitudes of signed areas rather than allowing cancellation.

This distinction becomes important in later kinematics.

Piecewise constant acceleration

A straight sloping segment on a speed–time graph has constant gradient.

Therefore acceleration is constant over that stage.

Different straight segments can represent different constant accelerations.

Curved speed–time graphs

If the graph is curved, the rate of change of speed varies with time.

Average rate of change of speed over an interval:

change in speed ÷ change in time.

Instantaneous rate of change of speed is the tangent gradient at one point, developed formally with calculus.

Distance under a curved graph

For an arbitrary curved speed–time graph, exact area may require calculus.

At school levels without integration, area may be:

  • estimated from rectangles or trapezia;
  • given in a shape that can be decomposed;
  • read from supplied information.

This creates a natural bridge into numerical and integral methods later.

Reading acceleration units

If speed is km/h and time is hours:

gradient units are:

(km/h)/h=km/h².

If speed is m/s and time is seconds:

gradient units are:

m/s².

Unit compatibility should be checked before calculating.

Mixed time units

If speed is in km/h but time is plotted in minutes, either:

  • convert time to hours before using speed×time for distance;
  • or convert speed into km/min.

Raw rectangle area in “km/h × minutes” is not yet kilometres until the units are reconciled.

A stage-table reconstruction

Suppose:

  • 0–4 s: acceleration from 0 to 12 m/s;
  • 4–10 s: constant 12 m/s;
  • 10–13 s: deceleration to 0.

The graph has:

  • upward straight line;
  • horizontal line at 12;
  • downward straight line to the axis.

Distance:

  • first triangle: 1/2×4×12=24 m;
  • rectangle: 6×12=72 m;
  • final triangle: 1/2×3×12=18 m.

Total=114 m.

Find unknown time from area

A vehicle travels at constant 15 m/s for t seconds and covers 120 m.

Rectangle area:

15t=120.

t=8 s.

Graph area can be used forwards or backwards.

Find unknown maximum speed from area

A triangular speed–time graph lasts 10 s and represents 150 m of travel.

Let maximum speed be v.

1/2×10×v=150.

5v=150.

v=30 m/s.

Compare two acceleration stages

Stage A:

0→20 m/s in 4 s gives 5 m/s².

Stage B:

20→30 m/s in 5 s gives 2 m/s².

Stage A has greater acceleration even though Stage B ends at a higher speed.

Speed is height; acceleration is slope. A higher graph is not automatically a more strongly accelerating graph.

Acceleration versus speed

An object can have:

  • high speed and zero acceleration;
  • low speed and high acceleration;
  • zero speed at one instant while acceleration is non-zero.

These quantities answer different questions.

Common misconception 1: gradient is speed

On a speed–time graph, graph height is speed; gradient is the rate of change of speed.

Common misconception 2: area is acceleration

Area has speed×time units, giving distance for a non-negative speed graph.

Common misconception 3: horizontal line means stopped

Only if the horizontal line lies at speed 0. A horizontal line above the axis means constant non-zero speed.

Common misconception 4: negative gradient means negative speed

Negative gradient means speed is decreasing. The graph may remain above zero.

Common misconception 5: speed–time graph below axis is ordinary negative speed

Speed is non-negative. A below-axis graph is more appropriately interpreted as velocity in a directional model.

Common misconception 6: graph area can be used without checking units

Time and speed units must be compatible before area becomes a physical distance.

A speed–time diagnostic ladder

  1. Can the learner read speed directly from graph height?
  2. Can the learner calculate acceleration from gradient?
  3. Can the learner identify constant speed?
  4. Can the learner identify rest at speed zero?
  5. Can the learner calculate rectangular area for distance?
  6. Can the learner calculate triangular and trapezium areas?
  7. Can the learner combine several stage areas?
  8. Can the learner distinguish speed from acceleration?
  9. Can the learner distinguish speed–time from velocity–time graphs?
  10. Can the learner reconcile units before using area?
  11. Can the learner solve reverse area problems for time or speed?

How this fits Secondary Mathematics

Speed–time graphs connect gradient, rates, mensuration, motion and later kinematics. They also provide one of the clearest examples of how the same graph carries two mathematical operations at once: slope describes change in speed, while area accumulates distance.

The deeper lesson: one graph can encode both change and accumulation

Gradient asks how fast the speed itself is changing.

Area asks how much movement has accumulated over time.

A speed–time graph is powerful because its geometry performs two jobs simultaneously: the slope measures the rate of change of speed, while the space beneath the graph adds up the distance produced by every moment of motion.

Sources and further reading